2020 Ford Explorer Backup System Problems

The contact owns a 2020 Ford Explorer. The contact stated that the vehicle was recently repaired under NHTSA Campaign Number: 25V159000 (Back Over Prevention); however, the vehicle experienced a failure with the back over prevention system. The contact stated that the image on the screen was occasionally blue, or the image was frozen. The contact had taken the vehicle back to the same dealer and was informed there would be a charge for a diagnostic test and the repair. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 65,000.

The contact owns a 2020 Ford Explorer. The contact stated that the vehicle was repaired under Ford Recall: 23S23/NHTSA Campaign Number: 23V342000 (Back Over Prevention); related to the Camera Blue Screen however, the repair failed to prevent the failure from occurring. The contact stated that approximately 3 years after the recall repair was completed, the digital screen failed to display the rearview image as intended and would reset once the rear door was opened and closed. The vehicle was taken back to the same local dealer and the contact was informed that the failure was not related to the recall repair and that a software update was needed. The vehicle was repaired out of pocket. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 35,000.

360 cameras are foggy and cannot see out of them causing false readings on parking alerts.This is the same issue the f150s have a recall about but there is not one for the explorer. The foggy display is getting worse over time. Hard to tell by the picture but in not very bright areas out of direct sun you cannot see anything on the 360 camera

The contact owns a 2020 Ford Explorer. The contact stated that the back over prevention camera screen was black intermittently. The contact then received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) and the vehicle was repaired; however, the failure persisted. The vehicle was returned to the dealer but was not diagnosed. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The manufacturer referred the contact to NHTSA Hotline to report the failure. The failure mileage was 52,700.

The contact owns a 2020 Ford Explorer. The contact stated that while operating the vehicle, the back over prevention camera malfunctioned and failed to display an image while the vehicle was in reverse(R). The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The contact stated that the vehicle had previously been repaired under NHTSA Campaign Number: 23V305000 (Back Over Prevention) for the failure. The failure mileage was 52,000.

The contact owns a 2020 Ford Explorer. The contact stated that while in reverse, the camera screen went blank. There were no warning lights illuminated. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention). However, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 40,000. Parts distribution disconnect.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the camera showed a blue screen when the vehicle was shifted into reverse. The contact stated that the failure was intermittent. The failure mileage was approximately 29,000. Parts distribution disconnect.

The contact owns a 2020 Ford Explorer. The contact stated while reversing, the rearview camera image turned black or blue. A message indicating that the rearview camera was inoperable was displayed. The contact stated that the vehicle was taken to the dealer, where an unknown software update was performed several times; however, the failure persisted. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted and referred the contact to the manufacturer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and referred the contact to the dealer for assistance. The failure mileage was approximately 16,000. VIN tool confirms parts not available.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention). The contact stated that while the vehicle was in reverse(R), the rear-view camera screen was blue. The vehicle was taken to a dealer where it was diagnosed that the rear-view camera needed to be replaced. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was 5,000.

My backup and 360 camera repeatedly fails. It maybe works 1% of the time. Ford is aware and has no resolution for the problem.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 21V735000 (Back Over Prevention) however, the part to do the recall repair was unavailable. The vehicle was taken to a dealer where it was diagnosed that the rear-view camera needed to be replaced. The vehicle was not repaired. The contact stated that the manufacture had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 20,000.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed the parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the camera became inoperable with the display screen going black. The vehicle had not been diagnosed or repaired. The failure mileage was unknown. VIN tool confirms parts not available.

When you put car in reverse the camera screen may go blue or black. Sometimes it is all in cone in rear, other times it’s on the right side and at other times it is the entire screen. Turning blue or black. This started in the first several months of ownership in 2020. The dealership tried several things including replacing the camera in 2020-2021-2022. Problem continued. Was told it was all fixed and the same day it happened again. I live in metro DC and have to park in small spaces often between cement pillars. I bought the car specifically for the camera system. I have hit things while attempting to get the camera back to useable again while in heavier car use areas buy not being able to see or have a sensor go off. Since 2020 Ford has had no viable remedy available. No option for new owners other than taking the loss on the car which as a widow I cannot afford to do.

The contact owns a 2020 Ford Explorer. The contact stated that while reversing at an undisclosed speed, the back over prevention camera displayed a black screen. The contact stated that the vehicle was taken to the dealer to be diagnosed. The contact was informed that the back over prevention camera needed to be replaced; however, the parts were not available. The contact stated that she had received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact later received a notification that referenced a temporary fix; however, when the vehicle was taken to the dealer, the contact was informed that there was no temporary fix available. The vehicle was not repaired. The manufacturer was made aware of the failure. VIN tool confirms parts not available.

The contact's wife owns a 2020 Ford Explorer. The contact stated that the rear-view camera was displaying a blue image on the screen while in reverse(R). The contact had taken the vehicle to a dealer and was initially informed that there would be a recall to address the failure. The contact then received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The vehicle had been taken to several dealers where repairs were made to the rear-view camera; however, the failure persisted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 500. VIN tool confirms parts not available.

360 degree camera is failing. The screen goes blue in reverse and i hit a garage wall unable to see it thru camera. Now the camera is failing in the front as well . Also is now occuring on a daily basis nor random anymore. Ford has not addressed the issue only thue software updates which i have has 2 occasions and yet camera still fails.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 23V022000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the rearview camera image turned black, blue or gray while reversing. The contact stated that the failure occurred increasingly. The messages "Reverse Brake Assist Not Available - See Owner’s Manual” and "Park Aid Fault" were displayed. The local dealer was not contacted. The vehicle was not diagnosed nor repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 58,000. VIN tool confirms parts not available.

The contact owns a 2020 Ford Explorer. The contact stated that there was a blue image on the rearview camera screen and a black image on the side-view cameras. The contact then received notification of NHTSA Campaign Number: 23V022000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 8,000. VIN tool confirms parts not available.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 23V022000 (Back Over Prevention) however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had experienced the failure. The failure mileage was unknown. VIN tool confirms parts not available.

The contact owns a 2020 Ford Escape. The contact received notification of NHTSA Campaign Number: 23V022000 (Back Over Prevention). The vehicle was taken to the dealer where the recall repair was performed; however, the contact stated that while shifted into reverse, the rear-view camera failed, and the screen display was blue. The vehicle was taken to the dealer where the contact was informed that the vehicle was previously repaired under 21V735000 (Back Over Prevention) and needed to be repaired again. The manufacturer was not notified of the failure. The failure mileage was approximately 100,000.

The contact owns a 2020 Ford Explorer. The contact stated that the rearview camera image was distorted. The contact related the failure to NHTSA Campaign Number: 23V022000 (Back Over Prevention). The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 40,000.

Despite bringing the vehicle in for two recall repairs, I still get the blue screen on the 360 camera when reversing. This limits my ability to safely back up and view my surroundings.

The contact owns a 2020 Ford Explorer. The contact stated upon starting the vehicle, a message indicating that the 360-degree camera was inoperable was displayed. The contact stated that the failure persisted while reversing. The contact also stated that the Blind Spot Information System (BLIS) that activated an indicator light in the side view mirrors when a vehicle was detected in the blind spot was malfunctioning as the sideview mirror indicator light failed to illuminate as needed. The vehicle was taken to the dealer, where the failure could not be duplicated; however, the failure persisted. The contact stated that the failure mostly occurred during cold weather. The contact received notification of NHTSA Campaign Number: 23V022000 (Back Over Prevention); however, the parts to do the recall repair were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and informed the contact that the recall was placed on hold on March 15, 2023. The vehicle was not repaired. The failure mileage was approximately 12,000. Parts distribution disconnect.

The contact owns a 2020 Ford Explorer. The contact stated that while reversing, the rear-view camera displayed a distorted image. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The contact related the failure to NHTSA Campaign Number: 23V022000 (Back Over Prevention) however, the VIN was not included in the recall. The failure mileage was approximately 17,700.

The vehicles rear view camera randomly displays a blue screen on reverse backup. All sensors go failing at times. Attached are some screens over the month. I have taken this to a dealership for a most recent recall fix (02/01/23) and it seems this issue never gets fixed. I keep getting notices of recalls and they claim they will patch it with software fixes but there seems to be more serious sensor issues . When this happens in a school zone it feels dangerous. This is a leased vehicle and I haven't received much help even from the manufacturers dealerships. Didn't find anyone to even listen to these issues. If we try to manually reverse the emergency braking comes into play from nowhere and applies itself due to these malfunctioning of sensors.

What component or system failed or malfunctioned, and is it available for inspection upon request? Rear back up camera How was your safety or the safety of others put at risk? The loss of the rear camera image while in reverse has increased my risk of crash. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, it has been to Holman Ford Turnersville many times for repair but the issue keeps occuring. I have been in touch with Ford directly and have two cases open. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? No warnings or symptoms

The contact owns a 2020 Ford Explorer. The contact stated while reversing, the 360-degree camera view became inoperable. There was no warning light illuminated. The dealer was contacted but offered no assistance. The manufacturer was contacted and informed the contact that the warranty on the vehicle was expired. The vehicle was not repaired. The failure mileage was 59,000.

The contact owns a 2020 Ford Explorer. The contact stated while reversing, the back-up camera image turned blue. There was no warning light illuminated. The contact stated that the failure occurred intermittently. The contact stated that the vehicle was taken to the dealer where it was repaired under NHTSA Campaign Number: 21V735000 (Back Over Prevention) however, the failure reoccurred a week later. The vehicle was taken back to the dealer where it was diagnosed that the back-up camera failed and needed to be replaced; however, the recall repair did not include a back-up camera replacement. The contact stated that the recall remedy failed to repair the failure. The manufacturer was notified of the failure and informed the contact that they could not assist as the VIN was not currently under recall. The vehicle was not repaired. The failure mileage was approximately 29,000.

The rear view camera system will intermittently display a blue screen. Dealer service has downloaded new software updates with no success.

The contact owns a 2020 Ford Explorer. The contact stated that the back-up camera intermittently displayed a blue screen while in use. The contact had taken the vehicle to the dealer on numerous occasions where software was used to clear the fault codes; however, the failure would return soon after the update. The manufacturer had been notified of the failure and informed him that his vehicle was not included in NHTSA Campaign Number: 21V735000 (Back Over Protection). The vehicle was not repaired. The failure mileage was approximately 1,000.

Rear camera screen turning blue when in reverse. Incident where child on bicycle crossing driveway put in danger.Appears to happen in afternoon with sun exposer on side of vehicle where camera is located. Taken to Ford dealer and had to purchase new camera system. Rear automated lift hatch also began opening when unattended and triggering alarm if parked. In addition it has released once while driving and caused alarm. Circuit board replaced at my expense has not resolved the problem. Each issue has happened multiple times during September and October 2022

The contact owns a 2020 Ford Explorer. The contact stated when the vehicle was shifted into reverse, there was no image displayed on the screen. The vehicle was taken to the dealer where the contact was informed that there was a recall for the failure. The contact stated a programming update was needed and was performed; however, the failure continued. The vehicle was taken back to the dealer where an update was completed several times; however, the failure persisted. The contact stated that the vehicle had been to the dealer at least 7 times to update the software. The manufacturer was notified of the issue and advised to go back to the dealer and a case was opened. The vehicle was taken back to the dealer for a 9-hour update. The contact stated that the dealer called and stated that the vehicle was out of warranty and the contact would be responsible for the repair. The VIN was not included in NHTSA Campaign Number: 21V735000 (Back Over Prevention). The approximate failure mileage was 28,000.

The backup camera display on the infotainment system when the vehicle is placed into reverse the screen illuminates in a blue screen not showing the surrounding area normally viewed. This issue was confirmed by Ford technician, an update to the system was supposed to fix the issue, the following day after the update to the vehicle, the same issue arose, I took the vehicle to the dealership, the issue was reproduced, the service writer documented the issue with a photo. This creates a backing safety issue as the proximity sensors where not working while in blue screen to warn of objects or persons while in reverse There where no warnings or onboard messages indicating an issue with the beck up camera This issue still has yet to been repaired by the dealership.

When engaging reverse the image on the screen turns solid blue. I can turn the vehicle off and back on and sometime this resoles the issue. It has happened at least a 12 times in the last couple of weeks. I did some initial investigation online and it appears that my vehicle is experiencing the same symptoms as a recall announced by Ford. https://www.consumerreports.org/car-recalls-defects/ford-and-lincoln-recall-2020-models-for-faulty-backup-cameras/

The contact owns a 2020 Ford Explorer. The contact stated while placing the gear shifter into reverse(R), the Back Over Protection screen turned blue. The side and front camera's functionality worked as intended. The vehicle was repaired under recall; however, the failure recurred several times. There were no warning lights illuminated. The vehicle was diagnosed at the local dealer with a defective camera. The camera was replaced. The manufacturer was notified of the failure. The approximate failure mileage was 50,000.

Backup camera display shows intermittent blue screen.

I have brought my vehicle to the dealership for repair of the Safety Recall for my car. They stated that they repaired the car. However the problem still exist. I have taken images and videos of the problem.

Reverse camera blue screen is appearing again after the 1st recall “fix”. Apparently this is becoming quite common, as I am in many Ford Explorer groups. Many others have this happening after their “recall fix” as well. Some even appear to have this happening after multiple times of recall “fixes”. Ford should be held accountable for not addressing a safety concern with a concrete solution. I have asked others within the groups to also submit incident reports.

Recall 21V735000 was performed by Sakelaris Ford of Rolla, Missouri on December 9, 2021. On February 28, 2022 the problem of the "Blue Screen" Backup Camera display again occurred and has been occurring regularly ever since. I have not yet contacted the dealer to reschedule a follow up pending correspondence from the NHTSA.

I have a safety recall notice 21S44/NHTSA RECALL 21V735 - 360 degree camera display, which includes the rear view camera may intermittently display a blue image on the media touchscreen upon shifting into reverse. Although your form said there was no recall on my vehicle I have received a notice mentioned above and I have experienced the problem mentioned in the recall notice a number of times. The Phil Long Ford Dealership in Colorado Springs on Motorcity .Drive have worked on the vehicle four times since the 1st of January and still have not repaired my vehicle. I would think that since this is a recall that they should have a fix by now. Any assistance you can provide would be greatly appreciated.

My rear camera works less than 50% of the time. It even goes out while backing up. I get a blue screen and my rear brake assist becomes inactive.

The rear back up camera area is blue and you are unable to see behind the vehicle.

The contact owns a 2020 Ford Explorer. The contact stated that while reversing, the rearview camera inadvertently turned blue. There were no warnings lights were illuminated. The contact received a recall notification for NHTSA Campaign Number: 21V735000 (Back Over Prevention) and the vehicle was taken to the dealer who updated the Image Processing Module software; however, the failure reoccurred 1-2 weeks later. The vehicle was taken back to the dealer who advised the contact that the rearview camera needed to be replaced and the repair would be completed at her own expense. The manufacturer was notified of the failure and followed up with the dealer. The manufacturer then called back but offered no further assistance. The vehicle was not repaired. The failure mileage was approximately 39,000.

The contact owns a 2020 Ford Explorer. The contact stated that while attempting to reverse the vehicle, the backup camera failed to function as designed. The contact stated that the backup sensor non-functional message was displayed. The vehicle was taken to a local dealer and was diagnosed IPMB updated and repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 21V735000 (Back Over Prevention). The vehicle was repaired under the recall but continued to experience failure. The manufacturer was not informed of the failure. The failure mileage was approximately 10,000.

Ford issued recall 21S44 for an intermittent back-up camera problem. I took my vehicle to Elk Grove Ford (95624) on 10/05/21 for recall repair. The problem continued and I took back on 10/19/21 to fix back-up camera. It still only works intermittently. Today, while backing up at an elementary school after my second recall service, my camera failed again. This is a critical safety issue which Ford knows about but has provided incompetent information to Elk Grove Ford. [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

Back up camera image distorts goes black at times but goes blue multiple times a day while driving and putting in reverse camera is blue 90% of the time

The contact owns a 2020 Ford Explorer. The contact stated while operating the vehicle the backup camera display image was very washed out, unclear and the colors appeared to be bleached out causing visibility issues for the driver. The vehicle was taken to the local dealer who replaced the camera display unit, but the failure persisted. The manufacturer was also notified of the failure. The failure mileage was 2,000.

Backup camera failed with a blue screen that was initially identified early August and brought into Ford 8/11-13 but dealership unable to reproduce problem. It is believed that the dealership re-booted the computer and downloaded new software. The same problem occurred just two days after we got the car back on 8/15 at which time a picture was taken to show the service department. A Google search suggested there was a problem with the back up camera for 2020 Explorer, but there was no recall on my VIN. After reaching out to Ford soon after we got the car back, a service person offered to order a new camera, but it was never approved. Numerous calls were placed to the dealership given ongoing camera failure and concern for causing an accident, but we were told that the problem needed to be reproduced. The camera could not be ordered. While backing the car out of our driveway without an operational camera or sensors, driver side rear bumper collided with a car parked in the street. The insurance company was notified the day of the accident and the car was taken to Ford body shop 9/21 where a repair estimate was provided. The dealership service department was notified that the car was involved in an accident because of camera failure and finally agreed to order a new replacement camera. On 9/23, we were notified of a "blue screen" back up camera recall.

I had an issue with the rearview backupcamera. The camera kept going out multiple times. I asked Fodd customer care if there was a recall and told me no. One day I was backing up at night my camera went out and I hit a mailbox which was in my blindspot I immediately called Ford to alert them that the camera went out a d I damaged my vehicle. Ford requested that I bring in my truck and changed the camera. They found out the camera had an electrical shortage. I attempted to get Forx to pay for the damages to my vehicle and they refused. The total estimate was 2700.00. The response why they denied my claim was I had an accident and they were not responsible regardless of the camera not working. They told me to contact my insurance to fix the damage. I feel I wouldn't have had an accident if my rearview camera did not go out. The backup assistance beep would have sensed the object behind me in my backup view and I would not have damaged my vehicle since the object was in my blind spot. I feel that Ford is responsible for the repairs and I have Video proof that my camera was having issues prior to my accident. I need Ford to fix my vehicle at no cost to me. They are ignoring the fact that the backup camera and blinspot assistance failed.

The contact owns a 2020 Ford Explorer. The contact stated while attempting to reverse the backup camera failed to engage. The contact stated that there was no warning light illuminated. The vehicle was taken to a local dealer where it was diagnosed with needing the Intelligent Platform Management Bus (IPMB) flashed. The vehicle was repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 21V735000 (Back Over Prevention). The vehicle was repaired but continued to experience the same symptoms. The manufacturer was informed of the failure and spoke with the contact’s attorneys and was awaiting a response. The failure mileage was approximately 22,900. Consumer stated camera was replaced 4 times and reprogrammed twice.

Reverse camera turns blue on many occasions and other times it gets dark, the engine in the mornings the engine sounds like a Diesel car in the dealer indicate it is normal but new vehicles do not sound that way.

We have returned the vehicle to the dealer 4 times for back-up camera / rear sensor failure. Most recently they had the vehicle from 8/16/2021 to 8/20/2021. Allegedly they replaced the back-up camera. On 8/27/2021 upon returning home from an approximately 3 mile drive, the back-up camera again failed while backing into our driveway. The DIC displayed the message "Back up assistance unavailable." While on vacation in Colorado, the back-up camera failed every day for 2 weeks (8/01/2021 - 8/13/2021). The failure would occur after extended drives at highway speed. On one occasion, the back-up display flickered between the image, blackout, and blue screen. On one occasion both the backup display and the overhead 360 display, displayed only blue screens. Turning off the vehicle and leaving it sit for 30 minutes or more clears the problem. The dealer claims they are unable to reproduce the problem. I have repeatedly told them that the vehicle must be driven for the problem to present itself. Repeatedly starting and shutting off of the vehicle while stationary will NOT produce the problem. We have repeatedly supplied images of the interior display showing the problem. This situation poses risk when reversing from parking place into oncoming traffic.

Back up camera not functioning properly. Back up camera will intermittently show distorted image while backing up and then it turns to black screen with warning stating "Camera is unavailable. Please contact your dealership."

Rear view camera not working. Dealer has confirmed however not able to get replacement part from manufacturer. Camera has been down for over 9 months.

Rear view mirror keeps turning solid blue ( blank ) and message center on the dash says "rear brake assist not working".

The contact owns a 2020 Ford Explorer. The contact stated while reversing the vehicle, the back over protection screen turned blue and the contact was unable to see the road. The contact stated that the reverse brake assist warning light was illuminated. The contact took the vehicle to the local dealer ten times within 11 months, but the mechanic was unable to diagnose the cause of the failure. The vehicle was not repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 5,100.

The contact owns a 2020 Ford Explorer. The contact stated the day he purchased the vehicle, the rearview camera turned blank as he was reversing out of the dealer parking lot. The warning message "Back Up Brake Assist Is Not Functioning" appeared on the instrument panel. The dealer diagnosed that the rear-view camera needed to be replaced. The contact stated that the vehicle was repaired however, the failure recurred while driving. The vehicle was taken back to the dealer and was repaired, however the failure persisted. The vehicle was taken back to the same dealer. The manufacturer was made aware of the failure and informed the contact that the VIN was not included in NHTSA campaign number: 20V575000 (Visibility) due to the manufactured date. A case was opened and the contact was referred to the NHTSA for assistance. The vehicle was not repaired. The approximate failure mileage was 10. Consumer stated 5th camera has been installed.

Rear camera goes blue,

TL* THE CONTACT OWNS A 2020 FORD EXPLORER. THE CONTACT STATED THAT UPON PURCHASE OF THE VEHICLE, THE REARVIEW CAMERA WOULD LOSE STREAM UPON USE AS THE REVERSE BRAKE ASSIST NOT AVAILABLE; SEE MANUAL WARNING MESSAGE WOULD ILLUMINATE ON THE INSTRUMENT PANEL. THE CONTACT SPOKE WITH TOMBALL FORD (22702 TX-249, TOMBALL, TX 77375) WHERE HE WAS INFORMED THAT THEY WERE UNAWARE OF ANY ISSUES WITH THE REARVIEW CAMERA HOWEVER, UPON INVESTIGATION, THE CONTACT DISCOVERED NHTSA CAMPAIGN NUMBER: 20V575000 (VISIBILITY) WHICH HE LINKED TO THE FAILURE. THE DEALER OFFERED TO REPAIR THE FAILURE HOWEVER, DECLINED TO REPAIR THE PART FOR FREE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND OFFERED NO ASSISTANCE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 20.

ALL CAMERAS INTERMITTENTLY NOT FUNCTIONING. DEALER REPLACED CAMERA MODULE. REAR CAMERA STILL NOT FUNCTIONING. SAID CURRENT RECALL FOR REAR CAMERA DOES NOT APPLY BECAUSE MY VEHICLE MANUFACTURER DATE IS OUT OF RANGE FOR RECALL. DEALER BLAMING REAR CAMERA NOT WORKING ON FORD ACCESSORY DASH CAMERA.

WHEN SWITCHED TO REVERSE, THE SCREEN TURNS BLUE AND SAYS REAR PARKING ASSIST DISABLED.